GS Carburetor Reconditioning 1

Finally got around to working on the GS over the weekend thanks to the wet & wild weather. Managed to remove the carburetors and begin stripping them down - man, there is no way this bike would have run for long had I not done so. Found a lot of loose hoses, screws and fittings and even the hose clamps around the rubber intake boots were loose. There was also a lot of dirt on and around the carbs - looks as if a wasp colony had at one stage decided to make it their home and left a few of their dead comrades in the casting holes of the carbys!!

After removing the carburetors I commenced on separating the four of them from their gang plate - from this point I plan to progressively strip, clean and reassemble one at a time in an effort to keep things as simple as possible. Nearly every screw (yes, they are screws, not socket heads!!) I have tried to remove has seized or is badly rusted, so it is slow going. Have been utilising my centre punch and hammer quite a bit to free these stuck screws and they will need replacing, but there are a few (especially on the the float bowl covers) that I have had to drill out. I am yet to get the first carb open (hopefully tonight), but looking in from the outside they don't seem like they are going to take too much work - not bad for a 28 year old bike.

Really is a learning process for me as I have never done anything like this before. I have an excellent set of instructions as well as a full set of O rings for the carb reconditioning courtesy of the GS Resources site and am planning to follow them as closely as possible. Reading what other guys have accomplished with these bikes really gives you the confidence and drive to do the same!!

Enjoying it so far.








Well, after stripping carb number one (in pic above) I have to say that I am glad I decided to do so. I found a lot of black sticky residue from old fuel and the float needle was near on impossible to remove from its sleeve - permanently stuck shut, which is not good when you consider that it is supposed to slide up and down dependent on the float assembly and feed fuel into the carb. Starting to make me realise why I couldn't get the bike to kick over!!!

The Strip Down Begins....

Had a bit of time on my hands on Friday night and so thought I would commence the strip down of the GS. I am still yet to get it to turn over, but believe that I have a problem with the starter motor, so will get onto that next. Anyway, I did manage to remove the rear guard, tank, covers and the exhaust (....I managed to shear two of the eight bolts in the process - what a prick - now I have to get them out). Once I had completed that I was able to see what I have to work with, and man, I now realise that I have a lot of work in front of me!!

It was very obvious that this bike had sat out in the weather for a fair period of time before the guy that I bought it off had picked it up, so it will need a good clean before I start to disassemble the carbs or motor. The wiring is pretty average and will need attention, the exhaust system is fairly well rusted and the carbs are filthy - and thats just a few things. Luckily, the motor doesn't appear too bad, although there is a fair bit of oil on the front, centered around the number two exhaust outlet. I am still unsure whether the oil is from a leaking gasket or it has blown out of the exhaust port - I just hope its a gasket!!

I look at this bike and I am so tempted to get stuck into the cosmetics, but my first goal is to get the motor running. After that, the carbs come off for a clean. Only once that has been accomplished will I turn to modifying the look of the bike.

My opinion so far....I think it will be a while before she is on the road!!

Side view

Sheared bolts after removing the exhaust system - bugger!!

Fair bit of oil on the front around the number two exhaust outlet - hidden by the frame

Tankless but filthy - that is what happens when left outside in the weather

I love the ass ends on these bikes - shaft drive really tidies em up!!

Carbs need a re-condition - have ordered parts for this already

Actually looks quite cool with the tail section removed

Another Suzuki - The Rat

I finally managed to pick up of my second Suzuki over the weekend, a shaft drive 1980 GS850 that I purchased off eBay for $700 whilst still in Kazakhstan. I bought it with the intention of having a cheap but reliable bike that I can do my daily commute on, as the GSX is really starting to clock up the miles. I plan to cut the rear off it and turn it into a single seater, with a rattle can paint job and just a few custom bits - nothing flash, just rat it.

I will post the results of any work that I do to it here, along with progress pics, so stay tuned!!





I like bits of all of the following GS's, so I am using these as examples on which to base mine...